STEEL
BUILT.
DELIVERED.

Commercial and industrial overhead doors in steel and insulated construction — manual, chain hoist, or electric operator. Sizes up to 24'W × 24'H standard, larger to order.

High-clearance bifold doors for aircraft hangars and large equipment storage. Electrically operated with manual backup, spans to 200' available.

Heavy-duty sliding barn doors and commercial swing doors for agricultural, industrial, and utility applications. Galvanized hardware rated for 25-year service.

Hollow metal walk doors with welded frames, weatherstripping, and hardware packages. Insulated cores for climate-controlled spaces. Fire-rated options available.

Counter-balance and motor-operated roll-up doors in galvanized slat for high-cycle applications — service bays, loading docks, storage units.

Single-hung and fixed metal windows with thermal breaks, plus fixed and operable louvers for ventilation openings. Flashed into wall panels on installation.

Annual inspection and lubrication of all overhead door operators, spring tension adjustment, safety reverse calibration, and remote reprogramming.

Mechanical and hydraulic dock levelers, dock seals and shelters, and wheel chocks for warehouse and distribution building installations.

Belt-drive and direct-drive wall-mount and roof-mount exhaust fans sized to your building's CFM requirements. Single-phase and three-phase available.

HVLS ceiling fans 8'–24' diameter for large open bays. Reduces perceived temperature by up to 10°F in summer, destratifies heat in winter.

Direct evaporative cooling units for dry climates — effective in warehouses, shops, and manufacturing without the cost of refrigerant-based AC.

Gas-fired radiant tube heaters and forced-air unit heaters for spot heating and whole-bay conditioning. Hung and connected by our crew.

Wind-driven and power-assist turbine ventilators for passive roof heat exhaust. Low maintenance, no electrical required for standard models.

Full CFM analysis and equipment layout for code-compliant ventilation in occupied buildings, chemical storage, and livestock facilities.

Bi-annual belt inspection, bearing lubrication, blade balance check, and motor amp draw testing for all installed ventilation equipment.

Penetration framing, curbing, and ductwork rough-in for industrial dust collection systems in woodworking, grain, and manufacturing facilities.

UFO and linear LED high-bay fixtures from 100W–400W for clear-span bay lighting. DLC-listed fixtures with 5-year warranty and 50,000-hour rated life.

Wall-pack and pole-mount LED security lights with photocell and motion controls. Dark-sky compliant fixtures for rural and commercial sites.

Electrical panel installation, conduit runs, junction boxes, and receptacle rough-in coordinated with your licensed electrician or our electrical subcontractor.

Standing seam roof prep and clamp attachment points for future solar panel arrays — no penetrations, no voided warranty.

Battery-backup LED exit signs and emergency egress lighting packages for code-compliant occupied building installations.

Pre-installed conduit runs and panel capacity provisions for future EV charging stations — installed during construction at a fraction of retrofit cost.

Data, security camera, access control, and PA system conduit and pull strings installed during building installation, before walls close up.

Transfer switch mounting, generator pad coordination, and fuel line rough-in for standby generator installations in critical-use facilities.

R-10 through R-38 fiberglass batts installed between purlins and girts with vapor retarder facing. Standard for climate-controlled agricultural and light commercial.

Closed-cell SPF applied directly to the interior of metal panels — highest R-value per inch, vapor barrier, and air seal in one application. R-6.5 per inch.

White-coated steel liner panels installed over insulation for clean, bright interiors — standard in food processing, cold storage, and finished commercial spaces.

EPS and polyiso rigid boards for under-slab, perimeter foundation, and above-deck applications. Installed per energy code requirements.

Single-layer and double-layer vinyl-backed condensation barrier systems for unheated buildings to prevent drip and corrosion on interior framing.

Foil-face radiant barriers under metal roofing for sun belt applications — reduces cooling loads by blocking radiant heat transfer in summer months.

Tongue-and-groove insulated metal panels (IMP) in R-25 through R-48 for refrigerated and freezer storage construction, with full system installation.

Infrared scan of existing metal buildings to identify air infiltration, insulation gaps, and thermal bridging — plus a remediation plan and cost estimate.